Warning:Before Using, Please Be Sure to Read and Understand All Safety Rules and Instructions in This Manual Before Operating the Heating Inductor. Pay Particular Attention to the Safety Rules. Failure to Follow All Instructions Listed Below May Result in Electric Shock, Fire, and/or Serious Personal Injury. Packing List ✔ Hbr Main*1 ✔ Flexible Soft Coil*1.1m ✔ 18mm Coil(Diameter of Bore)*1（Length 20cm) ✔ 22mm Coil(Diameter of Bore)*1（Length 20cm) ✔ 28mm Coil(Diameter of Bore)*1（Length 20cm) ✔ Manual * 1 MAGNETIC INDUCTION HEATER KIT Specification Model 110v Input Voltage 110v 50/60hz Input Current 7a Output Power 500-900w Output Voltage 45v Output Current 180a ✔General Safety 1) Keep a Fire Extinguisher or Fire Blanket Alongside at All Times When Using the Heating Inductor. 2) Ensure No FLammable Products Are near the Work Area While Using the Heating Inductor. 3) Do Not Use the Heating Inductor Within 150mm (6 Inches) of Any Air Bag Component. the Heat Created by the Heating Inductor Can Ignite the Air Bag Squib Propellant Causing It to Explode Without Warning. 4) the Heating Inductor Can Heat These Metallic Objects Very Quickly and Cause Serious Burns or Even Ignite Clothing. 5) Do Not Use an Attachment If the Insulation Has Been Breached. They Cannot Be Repaired, Only Replaced. 6) Ensure the Heating Inductor Is Connected to a Supply That Is Adequately Earthed. (Grounded) 7) Do Not Use the Heating Inductor in the Rain, Moisture or Immersed in Water. Exposing the Heating Inductor to Water or Other Liquids Can Cause an Electrical Shock Hazardpersonal Safety 8) If You Have a Cardiac Pacemaker or Any Other Kind of Electronic or Metal Surgical Implant Do Not Operate This Tool, and Always Stay at Least 1 Metre (Three Feet) Away from Anybody Operating It. 9) Although the Magnetic Fields Emitted by the Tool Only Travel a Few Inches, They Pose a Dangerous Risk to the Proper Operation of All Implanted Medical Electronic Devices in the User and Any Bystanders. 10) Do Not Operate the Heating Inductor While Wearing Any Metallic Items Such As Jewellery, (Including Ring, Watches, Chains, Identification Tags, Body Piercing) or Belt Buckles. 11) Do Not Wear Clothing That Contains Metallic Rivets, Waistband Buttons, Pocket Buttons or Zips When Operating the Heating Inductor. 12) Fumes and Smoke from Hot/Burning Adhesives Are Toxic. Wear an Appropriate Dual Filter (Dust and Fume) Mask. 13) Always Wear Heat-resistant Gloves When Using the Heating Inductor As It Heats Metal Very Quickly. It Can Be Easily Burn Your Hands and Fingers When Trying to Remove Parts from Hot Metal Surfaces. 14) Always Wear Heat-resistant Gloves When Using the Heating Inductor As It Heats Metal Very Quickly. It Can Be Easily Burn Your Hands and Fingers When Trying to Remove Parts from Hot Metal Surfaces. Do Not Touch the Coil, Rope Coil or Body Pad When the Heating Inductor Plugged into the Outlet. 15) Coils Will Be Hot After Use, Please Take Great Care When Fitting/Removing ✔Tool Safety 1. Before Plugging in the Heating Inductor, Make Sure That the Outlet Voltage Supplied Is Compatible with the Voltage Marked on the Label and Within 10% of the Stated Voltage. 2. Ensure Attachment Is Securely Located. Coil and Main Are Firmly Tightened Before Use. 3. Do Not Use the Heating Inductor for Longer than the Stated Duty Cycle: 5 Minutes on Followed by 5 Minutes off. the Main Circuit Board Has an Overheat Protection Device, However the Attachments Do Not Have Overheat Protection so Should Not Be Used for More than 5 Minutes of Continued Use. 4. Please Ensure That the Cooling Fan Is Running When the Power Switch Is Operated, If the Fan Does Not Run Do Not Use the Heating Inductor 5. Do Not Attempt to Create More than 4 Coils When Using the FLexible Soft Coil, a Minimum of 2 Coils and a Maximum 3 to 4 Coils Is the Optimum Number Needed for Best Operation. ✔Operation 1) to Prolong Your Heating Inductor, Leaving an 10mm Air Gap Between the Coil and the Work Piece Is Recommended As the Insulation of the Coil Will Eventually Burn Through If Held Directly to Hot Material. 2) Choose the Appropriately Sized Coil to Give the Closest Fit to the Work Piece. 3) Insert Both Ends of the Coil into the Coil Location Socket and Tighten the Thumb Securely. 4) Activate the Power Switch to Run the Heating Inductor for 1-3 Minutes Until Enough Heat Has Been Applied to the Work Piece to Break the Rust/Corrosion Bond. 5) Release the Power Switch to Turn off the Power. 6) Turn Unit off and Allow the Unit and All Attachments to Cool for at Least 20 Minutes. Handling the Unit or Parts Before They Have Cooled May Result in Injury. Condition New Type Heating Bolt Remover Drive Induction Coil Heater Features With LED Lights, Lightweight, Flexible Soft Coil, Flameless Power Source Corded Electric Input Voltage 110V Input Current 7A Output Voltage 45V Output Power 500-900W Output Current 180A
