Premium Glass Cutting Tool Kit for Thick Glass - Diamond Drill Bits with Guide for Drilling Holes in Glass Bottles, Blocks, Clay Pots, Cups & Plates - Perfect for DIY Crafts, Home Improvement & Glass Art Projects

Glass Cutter – Not just any Glass Cutting Tool The Amazing Glass Cutter made in UK a manual Glass Cutter that lets you cut straight radius and wavy lines in glass mirror, stained glass and glass tiles. The scoring wheel is not sharp, it is probably the dullest tool you will own but the hardest, the hardness of the cutter blade along with the special angle ground into the scoring wheel allows The Amazing Glass Cutter to cut thick and thin glass materials and even Hard Tile without hurting the wheel. The Secret to using The Amazing Glass Cutter is to follow the instructions carefully. Practice on a spare piece in order to work out enough pressure to apply, usually not enough pressure is applied to start with but sometimes less pressure is better so practice makes perfect. Cutting on the floor instead of on a solid board at waist height will fail and give uneven pressure along the score line and may even crack glass. Not oiling the scoring wheel and making sure it is turning very freely may cause the wheel to bind, drag and even lock up and just scratch the glass instead of evenly scoring it and this will prevent the glass cutter from working correctly. Holding the Glass Cutter by the plastic grips when scoring with your strongest hand means that you are only applying minimal amount of pressure if any on the cutting wheel at the point where the scoring is happening. Always Pull towards you not push Away. For Stained Glass, Plate Glass, Picture Framing Glass or Fused Glass the cutting wheel should be oiled every single score, oil will run down onto the glass and will not only cool down the glass and give a cleaner cut it will also extend the life of the cutting wheel. If you can wipe the oil off the glass and there is no score line visible, then you need to increase the pressure – make sure you are holding close to the wheel and use the 2 handed method if needed especially if you do not have a lot of strength in your hands or are cutting a very hard material.

GLASS CUTTING KIT- Watch Glass Cutting Videos Read Tips And Instructions and Download User Guide. Must Soak Glass Cutting Tool Wheel in Glass Cutting Oil, Run Wheel Up And Down A Board To Check Wheel is Spinning Freely So It Can Score Glass Evenly If Glass Cutting Blade Stops It Will Not Score. Glass Cutter Wheel Must Be Oiled Every Cut, A Dry Wheel Will Stick and Drag Across And That Will Not Make a Good Score. Practice On Scrap Glass Before Making Final Cut To Ensure You Have The Technique.

HOLD GLASS CUTTER TOOL – Handles Of Glass Cutter Tool Are Only For Squeezing Glass To Break, Do Not Hold Glass Cutter by Handles When Scoring. Hold Close To The Wheel for Control And Pressure on Glass Scorer. The Technique is to Create A Small V In Surface Of Glass Sheet. Scoring Way Too Hard Or Without Oiling Wheel Leaves A Wide Groove And White Dusty Line that Will Not Break On The Line Instead Of A Shallow V, The Perfect Glass Score Must Be Just Firm Enough To Leave the V Score in Glass.

CUT STRAIGHT LINE IN GLASS – Place Glass Sheet On A Board At Waist Height, Scoring Glass on A Soft Carpet, Scoring Too Hard or More Than Once Will Cause Glass To Shatter When You Go to Break Glass. Draw A Line On Glass With A Marker, Follow Line By Pulling Cutter Towards You, Never Push Away, Watch The Back Of The Glass Cutter Wheel to Keep on Line or Use Flat Side Of Glass Cutting Wheel To Run Along A Very Smooth Straight Edge Guide At Least 2mm Thick, Guide Can Be Taped Down To Prevent Moving.

GLASS DRILL BIT – 3/16” ¼” ½” Drill Bit For Glass Drill Bit For Bottles, These Glass Cutting Drill Bits For Drilling Holes In Glass Are To Be Used Wet, Glass Drilling Bits Will Also Drill Holes In Porcelain Tile So Not Just Drill Bits For Glass Sheet Also A Drill Bit For Glass Bottles And Drilling Holes In Glass Blocks For Making Wine Bottle Lamps And Lights. The ½” Glass Drill Bit is the Perfect size for Tree Lights to Push Through. On Flat Surfaces the Guides can be used To Hold Bits Straight

TILE DRILL BITS – 3/16 Tile Drill Bit ¼ Tile Drill Bit Spear Point Tile and Glass Drill Bits Can Be Used For Drilling Holes In Glass At Low Speed In A Drill Press Is Best. Drill Holes In Clay Pots Drill Holes For Drainage in Pots Drill Holes In China Plates And Cups. Build A Wall Around Area With Plumbers Putty Fill With Water To Create A Well Of Coolant. These Tungsten Pointed Tile Drill Bits can be used for Drilling Holes in Ceramic Tiles For Screw Holes for Grab Bars and Shower Doors.